Search Results - The AK Forum

Search:

Type: Posts; User: MR - E

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. 264447I gun please, will buy a scope later, hope...

    264447I gun please, will buy a scope later, hope it comes with mounting plate
  2. Replies
    14
    Views
    307

    I have a general headspace question. I own 2...

    I have a general headspace question. I own 2 AKs, one runs perfectly - in it the cartridge groove & base lip only - protrude from the breach.

    *problem AK: Almost an eighth of an inch MORE of...
  3. Replies
    21
    Views
    593

    ** NO BINDING - just slight resistance when...

    ** NO BINDING - just slight resistance when hammer is cocked, & less as it slides closed across it.

    ** I DO HAVE A HEAD SPACE QUESTION .. the cartridge slides in & out of the breech nicely - But -...
  4. Replies
    21
    Views
    593

    5/25/19 The new parts I added were unnecessary - ...

    5/25/19 The new parts I added were unnecessary - Still Jams - but adding a FAILURE TO FEED to FAILURE TO EJECT. I now know that recoil spring, extractor & spring, or gas passage blockage is not the...
  5. Neat AK Recoil Spring, & good experience with 2 vendors

    Hello all, I just purchased & installed a new (& special) AK Recoil Spring made by ALG Defense, & sold by AK47 operators union. It has several tightly wound coils in its middle where the center link...
  6. Replies
    18
    Views
    511

    I do not have a better photo of it yet, but It...

    I do not have a better photo of it yet, but It is the same scope mount plate VEPRs come with. My SAR-1 also came with that same scope mount factory applied - when the rivets went in.. I found my...
  7. Replies
    18
    Views
    511

    263453263455263457Here are photos of my SA 2000M....

    263453263455263457Here are photos of my SA 2000M. Its wooden stock is a bit longer than others, & fits me best of AKs I own or have tried. Since all parts are serial #d to match, indicates it was...
  8. Replies
    21
    Views
    593

    Here's another pic.

    Here's another pic.
  9. Replies
    21
    Views
    593

    Fixed ???

    All new springs & NEW Hungarian Extractor claw are in it - hopefully will function properly. the new recoil spring means business compare to original. All serial numbers match on all main parts =...
  10. Replies
    21
    Views
    593

    So, I sent off for one of the special wound ALG...

    So, I sent off for one of the special wound ALG recoil springs - as its cost compared to others, & it seems like a good concept.
    Also invested in a NEW Hungarian extractor & spring. VERY GOOD DEAL...
  11. Replacement FEG SA2000M AK Parts ? Gas Block question ?

    I think I may have sorted it out. see pix in above post
  12. Replies
    21
    Views
    593

    OK, I'll take pix & post soon. Although I haven't...

    OK, I'll take pix & post soon. Although I haven't been able to spot anything abnormal myself.
    I did notice a nick on the inside of my dust cover - about where ejected shells might have hit it. I...
  13. Replies
    929
    Views
    37,932

    Poll: SLIGHTLY OFF SUBJECT - but, FEG made some...

    SLIGHTLY OFF SUBJECT - but, FEG made some remarkable Pistols as well. I own two 9mm HI POWER clones. I really like them.
  14. Replies
    21
    Views
    593

    HI Fuss, I disassembled the bolt & cleaned &...

    HI Fuss,
    I disassembled the bolt & cleaned & inspected everything. the Extractor claw is fine & I cleaned behind it - its spring is made from 2 wires wrapped, & is still like new. I began to suspect...
  15. Replies
    21
    Views
    593

    BTW, I had one suggestion from elsewhere - to...

    BTW, I had one suggestion from elsewhere - to install a new ejector & spring + recoil spring. No idea if just any AK parts will fit the SA2000m, or the best place to look for them ? Another thing...
  16. Replies
    21
    Views
    593

    I'm almost embarrassed to - because its been so...

    I'm almost embarrassed to - because its been so long. I got busy with other things, Then had a physical problem - but finally got it to the Range. MORE embarrassment, everybody asks about it &...
  17. Replies
    15
    Views
    839

    All the Above Muzzle brake advice sounds good. I...

    All the Above Muzzle brake advice sounds good. I have over the years (I'm 72) blown out both rotator cuffs, & they healed pretty well without surgery. That being said, at the time I bought my first...
  18. Replies
    21
    Views
    593

    I removed the buffer pad & have looked everything...

    I removed the buffer pad & have looked everything over, & all seems in order - but I won't know for sure until I can get it out to the range to fire. till then a "Mystery".

    The FEGs workmanship is...
  19. Thread: Sar-1

    by MR - E
    Replies
    24
    Views
    832

    Question, Back when I bought my SAR-1 it was...

    Question, Back when I bought my SAR-1 it was under $300. I had put USA made parts & furniture on it - so I'd have the required number USA made parts - in order to use the Romanian RIGHT SIDE folding...
  20. Replies
    4
    Views
    563

    My Favorite folding stock is the sturdy Romanian...

    My Favorite folding stock is the sturdy Romanian RIGHT SIDE folder. It is thick forged black steel with a black oxide finish (which goes with any furniture) & is historically & aesthetically correct....
  21. Prior to buying my SAR-1 20 years ago, the only...

    Prior to buying my SAR-1 20 years ago, the only rifle I owned was a Winchester 94 lever action 30-30 carbine - which I sold immediately after trying out my new AK.
    I also sold my Remington...
  22. FOR SALE: 1 LED UPGRADE KIT FOR RUSSIAN SCOPE: ...

    FOR SALE: 1 LED UPGRADE KIT FOR RUSSIAN SCOPE: includes LONG BATTERY CAP that converts scope body to use one AA 1.5 volt battery. + 2, 1.5 volt red LED BULBS.

    Kit is here in the USA, selling for...
  23. Replies
    1
    Views
    218

    This looks similar to one I had. I had bought it...

    This looks similar to one I had. I had bought it for my AK, but found that its legs were not tall enough to clear my dust cover. Also the clasp assembly was not compatible with the SAIGA style rail...
  24. *I Finally was able to test my Scope (above). I...

    *I Finally was able to test my Scope (above). I am using a Saiga rail, it is located perfectly on the rifle, with excellent eye relief & scope height. With the 4 power scope I could see the target...
  25. I had no problem drilling my FEG SA2000M receiver...

    I had no problem drilling my FEG SA2000M receiver with a USA made HS Drill bit. Just don't drill near a spot weld where it's extra hardened.
Results 1 to 25 of 44
Page 1 of 2 1 2